• ESXi host Upgrades
    • Upgrading vCSA from 6.5 to 6.7U2 Undo

      Production environment, upgrading VMWare vCSA from 6.5 to 6.7U2. Will be working with VMWare and following the standard procedure for upgrading the vCSA. Wanted to double check my Zerto process. Should I stop the Zerto Virtual Manager service prior to starting the vCSA upgrade?

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 10, 2019
    • Delta Sync Question

      This morning we put a few hosts into Maintenance Mode. At that time, Zerto started Delta Syncing volumes. Maintenance on those hosts has been completed. We’d like to know if we should wait until the Delta Syncs are complete or if we can put the hosts back into production? If we do put the hosts […]

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 10, 2019
    • vCenter & Host 5.1 Migration

      Hello everyone. I need some suggestion for my up coming migration task. Below is my current setup: – ESXi 5.1 U3 – vCenter 5.1 (with about 30VMs) – Zerto 6.0U1 We will be undergoing full infra upgrade, so we will be upgrading from current ESXi 5.1 to 6.5, vCenter 5.1 to 6.5 as well. So […]

      in: VMware

    • People: 1
      Replies: 0
    • September 10, 2019
    • Zerto Upgrade

      Is there any recommendation from Zerto to upgrade ptotected site first and then upgrade the recovery site? We have a shared DR site running 6.0U4P1 which is paired to 3 other protected sites running 6.0U4P1 and 6.5U3P1, behind a ZCM. So, after upgrading ZCM to 6.5U4, can we upgrade the recovery site ZVM to 6.5U4?

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 10, 2019
    • ZVR update to v6.5 U4

      I updated our Zerto Virtual Manager from version 6.5 Update 3 Patch 1 to version 6.5 Update 4 today. The update completed without errors. However, I noticed that the “VRA Version” column on ZVM GUI still shows “Latest” as its status (i.e. not “Outdated”). I already refreshed the browser and even rebooted our updated ZVM. […]

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 10, 2019
    • O2M with multtiple sites in a Zorg

      We are a CSP.  We have a client with 2 production sites in their Zorg replicating to our cloud. Will O2M allow the client to replicate from one of their sites to the other?  If one of the VPGs is failed over to our DR site, can it be edited to replicate to the other […]

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 10, 2019
    • Multiple Sites Replication.

      <p class=”x_MsoNormal”>Hello team,</p> <p class=”x_MsoNormal”>I have a question: about Zerto multiple sites replication:</p> <p class=”x_MsoNormal”>As the following scenario: replicate site <b>A</b> to Site <b>B</b>, then replicate Site <b>B</b> to Site <b>C</b>, is that possible?</p> <p class=”x_MsoNormal”>Ca we perform like above scenario? Assuming the active site is: A, B still passive , for our reasons we would like to do a replication […]

      in: Support Q & A

    • People: 4
      Replies: 4
    • September 9, 2019
    • ZCM VM Upgrade

      Hi, This is just a general question looking for some guidance. We will be upgrading the VM that hosts our ZCM from W2008 to W2016. We have a method to use for upgrading ZVM VMs, would this work for a ZCM? I attached the guide for review.

      in: Support Q & A

    • People: 3
      Replies: 2
    • September 9, 2019
    • Syncs due to host maintenance

      Posting this case on behalf of Moti.G: VPGs started to Bitmap and Delta sync after patches were applied on hosts running the protected VMs which took hours to complete (especially the Delta sync) . Is this an expected behavior?

      in: Support Q & A

    • People: 1
      Replies: 1
    • September 9, 2019
    • Gerry Oconnor – Renaming of VM's in vCD

      Hi, We have a customer who we have setup in vCD and we have setup an Zorg for them and created the VPG’s and all is working fine. However the customer has renamed the hostname of some of the servers. We want to rename the VM’s in vCD to reflect the new hostnames (and prevent […]

      in: Support Q & A

    • People: 3
      Replies: 2
    • September 9, 2019
    • Upgrade question – Hosted Services

      Hello, I’ve got an upgrade question. We are currently on version 6.5u4 on our recovery site, with most of our customers being on version 6.0u4 on the source sites. We are now looking to upgrade to version 7, but understand we’ll need to get our customers to within one version of our own first. My […]

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 9, 2019
    • Upgrade Zerto from 6.0 to 6.5

      Hi, we are looking to update our VMware environment from 6.5 update 2 to 6.5 update 3. However our Zerto environment is on 6.0 update 3 which is not supported. Could you please let me know the relevant info/steps to update Zerto to version 6.5 update 4 making it compatible for the VMware upgrade. Thanks […]

      in: Support Q & A

    • People: 1
      Replies: 1
    • September 9, 2019
    • Zerto networks – best practice

      Building new zerto env. what are best practice of on which networks should VRA, ZVM ,ZCM ,ZCC should be on? Example, if we put VRA on management network , how does the replication traffic impacts the management traffic? Storage VLAN is preferred for VRA? Any examples when NSX is being used?

      in: Support Q & A

    • People: 2
      Replies: 1
    • September 9, 2019
1 2 3 … 62 63 64 … 119 120 121